High Current Active Alarm Buzzer Driver Module

Specification:-

1. Better than passive buzzer modules
2. Operating voltage:  3.3V - 5V
3. Fixed bolt holes for easy installation
4. Programmable and easy to control
5. This module is driven by an S8550 triode

5v Piezoelectric Buzzer Beeper Alarm

SPECIFICATIONS:-

• Type: Piezoelectric Buzzer
• Length: 9.5mm
• Diameter: 12 mm
• Input Voltage: 5-20v
• Current: <25MA
• Color: Black
• Low Power Consumption Device

3V to 24V Cylindrical Piezoelectric passive continuous beep buzzer pack of 2pcs

Specification:-

1. Operating voltage range: 3V to 24V
2. Rated current: 3A
3. Response frequency: 2048Hz
4. Sound pressure : 95db/10cm
5. Two electric wires for connection
6. Hard plastic body

5V Mini Piezoelectric passive continuous beep buzzer pack of 2pcs

Specification:-

1. Operating voltage : 5V
2. Rated current : 30mA
3. Response frequency : 2048Hz
4. Sound pressure : 80db/10cm
5. Pin spacing : 8mm
6. Hard plastic body

220V AC Cylindrical Piezoelectric passive discontinuity beep buzzers pack of 10pcs

Specification:-

1. Operating voltage range: 200V to 220V AC
2. Rated current: 5A
3. Response frequency: 2048Hz
4. Sound pressure : 95db/10cm
5. Two electric wires for connection
6. Hard plastic body

6V to 24V Cylindrical Piezoelectric passive continuous beep buzzer with ring crimp connector pack of 2pcs

Specification:-

1. Operating voltage range : 6V to 24V
2. Rated current : 3A
3. Response frequency : 2048Hz
4. Sound pressure : 95db/10cm
5. Two electric wires for connection
6. Hard plastic body

220V AC Cylindrical Piezoelectric passive discontinuity beep buzzer pack of 2pcs

Specification:-

1. Operating voltage range : 200V to 220V AC
2. Rated current : 5A
3. Response frequency : 2048Hz
4. Sound pressure : 95db/10cm
5. Two electric wire for connection
6. Hard plastic body

220V AC Cylindrical Piezoelectric passives discontinuity beep buzzers pack of 100pcs

Specification

1. Operating voltage range : 200V to 220V AC
2. Rated current : 5A
3. Response frequency : 2048Hz
4. Sound pressure : 95db/10cm
5. Two electric wires for connection
6. Hard plastic body

3V to 24V Cylindrical Piezoelectric passive continuous beep buzzers pack of 10pcs

Specification:-

1. Operating voltage range : 3V to 24V
2. Rated current : 3A
3. Response frequency : 2048Hz
4. Sound pressure : 95db/10cm
5. Two electric wires for connection
6. Hard plastic body

3V to 24V Cylindrical Piezoelectric passives continuous beep buzzers pack of 100pcs

Specifications:-

1. Operating voltage range : 3V to 24V
2. Rated current : 3A
3. Response frequency : 2048Hz
4. Sound pressure : 95db/10cm
5. Two electric wires for connection
6. Hard plastic body

5V Mini Piezoelectric passive continuous beep buzzers pack of 10pcs

Specification:-

1. Operating voltage : 5V
2. Rated current : 30mA
3. Response frequency : 2048Hz
4. Sound pressure : 80db/10cm
5. Pin spacing : 8mm
6. Hard plastic body

5V Mini Piezoelectric passives continuous beep buzzers pack of 100pcs

Specification:-

1. Operating voltage: 5V
2. Rated current: 30mA
3. Response frequency: 2048Hz
4. Sound pressure : 80db/10cm
5. Pin spacing: 8mm
6. Hard plastic body

6V to 24V Cylindrical Piezoelectric passive continuous beep buzzer with ring crimp connectors pack of 10pcs

Specification:-

1. Operating voltage range : 6V to 24V
2. Rated current : 3A
3. Response frequency : 2048Hz
4. Sound pressure : 95db/10cm
5. Two electric wires for connection
6. Hard plastic body

6V to 24V Cylindrical Piezoelectric passive continuous beep buzzers with ring crimp connectors pack of 100pcs

Specification:-

1. Operating voltage range : 6V to 24V
2. Rated current : 3A
3. Response frequency : 2048Hz
4. Sound pressure : 95db/10cm
5. Two electric wires for connection
6. Hard plastic body

28 in One Mini starter kit for beginners (motor, battery, switch, alligator clip, buzzer, resistor, led, propeller)

Specification

1. 100% Best quality and Branded Products
2. 28 Items for hobbyists and professionals
3. Starter pack for little ones
4. Includes all the basic things you need
5. Excellent choice for a starter pack

220V 20mA AC flush panel mount LED Indicator light Alarm with buzzer Red color

Specifications

1. Operating voltage : up to 220V AC
2. Operating current : 20mA
3. Viewing angle : 30° to 110°
4. Emerging color : RED
5. Life expectancy : 1,00,000 hours
6. Buzzer for alarm system
7. Precise and smart design

Combo of 70mm x 70mm Solar Panel with Micro Dynamo Motor and Piezoelectric Buzzer

Specifications:-

1. Solar panel
   1. High-quality product
   2. 100% user satisfaction
   3. High quality polycrystalline solar panel
   4. Output voltage : 6V
   5. Current range : 100mAh
2. Motor
   1. Operating voltage : 3.5V to 9V DC
   2. Rated RPM : 16000
   3. Compact-sized
   4. High performance
   5. Long shaft
3. Buzzer
   1. Operating voltage range : 3V to 24V
   2. Rated current : 3A
   3. Response frequency : 2048Hz
   4. Sound pressure : 95db/10cm
   5. Two electric wires for connection

Diy Mini School Projects Kit (Motor Battery Buzzer Kit For Hobbyists And School& College Students) Starter Kit With Video Tutorial & User Manual

Specification

• 100% Best quality and Branded Products
• Diy Mini School Projects Kit
• User Manual & Video Tutorial 
• Battery Holder
• Push Connector
• Buzzer 
• Excellent choice for a starter pack

Diy Mini Tilt Sensor Kit (led, Push Connector,buzzer,tilt Switch Starter Kit With Video Tutorial & User Manual

Specification

• 100% Best quality and Branded Products
• Diy Mini Tilt Sensor Kit
• User Manual & Video Tutorial 
• Battery Holder
• Push Connector
• Buzzer 
• Tilt Switch
• Excellent choice for a starter pack

Diy Mini School Project Kit 2 (Motor Battery Buzzer Push Switch Kit For Hobbyists And School& College Students) Starter Kit With Video Tutorial & User Manual

Specification

• 100% Best quality and Branded Products
• Diy Mini School Projects Kit
• User Manual & Video Tutorial 
• Battery Holder
• Push Connector
• Switch
• Buzzer
• Excellent choice for a starter pack

DIY Mini IR Detector Kit With User Mannual And Video Tutorial

Specification

1. 100% Best quality and Branded Products
2. Diy Mini Ir Detector Kit
3. User Manual & Video Tutorial 
4. Battery Holder
5. Push Connector
6. Ir Sensor
7. Buzzer
8. It comes with a user manual, a detailed video tutorial, and all the necessary materials.
9. Excellent choice for a starter pack

DIY Mini IR signal detector kit ( Battery Holder, Push Connector, IR sensor, Led, Cell’s, Buzzer) with User Manual and Video Tutorial

Specification : 

• 100% Best quality and Branded Products
• Diy Mini IR signal detector kit
• The kits are easy to assemble and come with a build guide
• Very easy to make and the parts are easy to find
• Excellent choice for a starter pack

DIY Mini Motion Sensor Kit ( Battery Holder, Push Connector, Motion sensor, Led, Cell’s, Buzzer) with User Manual and Video Tutorial

Specification:

• 100% Best quality and Branded Products
• Diy Mini Motion Sensor Kit
• The kits are easy to assemble and come with a build guide
• Very easy to make and the parts are easy to find
• Excellent choice for a starter pack

12V DC 100 Watt Inverter Circuit Board with Relay and Buzzer (110mm x 60mm x 2mm)

Specification

• Input voltage: 12V DC
• Power rating: 100 Watt
• Frequency : 50HZ/60HZ
• Inbuilt over voltage, over current, and short circuit protection
• Simple and easy-to-use design
• Fast transient response
• Dimension: 110 x 60 x 2 mm
• It's capable of operating CFL bulbs, LED bulbs, bulb, Light Charger, etc.
• It's not capable of electromagnetic transformer devices

DIY Electronics Kit with Motors, Propellers | Switches | LEDs | Buzzers & Battery Components (35+ Items)

Specification

• High-speed DC toy motor
• 9V battery clip connector
• Multi-color LED 
• Two-meter wire, red and black 
• High-reliability 1K ohm (Ω) resistor
• SPST red-colored plastic rocker switch
• Hard-quality, complex plastic propellers
• Non-rechargeable heavy-duty battery
• A buzzer is a type of sound device that basically generates sound signals
• Basic Electronics projects
• 100% Original and best quality product

12V Piezoelectric Buzzer Beeper Alarm Pack of 2

Specifications:-

• Type: Piezoelectric Buzzer
• Length: 9.5mm
• Diameter: 12 mm
• Input Voltage: 9-12V
• Current: <25MA
• Color: Black
• Low Power Consumption Device

12V Piezoelectric Buzzer Beeper Alarm Pack of 10

Specifications:-

• Type: Piezoelectric Buzzer
• Length: 9.5mm
• Diameter: 12 mm
• Input Voltage: 9-12V
• Current: <25MA
• Color: Black
• Low Power Consumption Device

12V Piezoelectric Buzzer Beeper Alarm Pack of 100

Specifications:-

• Type: Piezoelectric Buzzer
• Length: 9.5mm
• Diameter: 12 mm
• Input Voltage: 9-12V
• Current: <25MA
• Color: Black
• Low Power Consumption Device

DIY Rectangle Solar Panel Kit with Buzzer | Motor | LED & Fan | STEM School Project Kit

Specification:-

• 12V toy Motor
• 3V to 24V beep buzzer
• 80X40 mm 6V-100mAh Solar
• High-quality product
• 4-blade propeller 
• Red and yellow color LEDs round shape
• Material: Hard Plastic

Package Includes: 80X40mm Solar (Rectangle), Round toy motor, Big Buzzer, Wire, Switch, Led Bulb, Toy fan

DIY Square Solar Panel Kit with Buzzer | Motor | LED & Fan | STEM School Project Kit

Specification:-

• 12V toy Motor
• 3V to 24V beep buzzer
• 55 x 55mm, 6V-50mAh Solar panel
• High-quality product
• 4-blade propeller 
• Red and yellow color LEDs round shape
• Material: Hard Plastic

Package Includes: 55 x 55mm Solar (Square), Round toy motor, Big Buzzer, Wire, Switch, Led Bulb, Toy fan

DIY Circle Solar Panel Kit with Buzzer | Motor | LED & Fan | STEM School Project Kit

Specification:-

• 12V toy Motor
• 3V to 24V beep buzzer
• 6V, 80mAh, circle-shaped solar panel
• High-quality product
• 4-blade propeller 
• SPST small rocker switch
• Red and yellow color LEDs round shape
• Material: Hard Plastic

Package Includes: 6V 80mAh Circle shape Solar panel Round toy motor, Big Buzzer, Wire, Switch, Led Bulb, Toy fan

Combo of Mini Electronics Components with Buzzer, Switch Button, Ic's, LEDs, Potentiometer, Resistor, Capacitor etc.

Specifications:-

• 5V RGB multicolor 5mm  LED
• The kit includes various ICs
• Different resistance values
• 5V Piezoelectric Buzzer Beeper Alarm
• Capacitors store and release electrical energy.
• Black-colored tactile momentary push-button switches
• The potentiometer is a variable resistor that enables precise control over the resistance in a circuit

Package Included:- 5mm Led- White, Red, Blue, Green, Yellow- (10Pcs each), 5mm RGB LED 4PIN COLOR CHANGING-1pcs, Photoresistor- 2pcs, Thermistor - 1pcs, Diode Rectifier (1N4007)- 5pcs, NPN Transistor (2N2222)- 5pcs, IC - 4N35, SN74HC164- (1Pcs each), Tactile switch Button (small)- 10pcs, Passive Buzzer- 1pcs, Vertical Potentiometer-1pcs, Ceramic Capacitor-104, 224 Capacitor-(10pcs each), Electrolytic Capacitor- (10UF 50V), (100UF 50V)- (5pcs each ), Resistor - 10K, 100K, 220RK ,330K , 1K, 22K, 5.6k, 10K,100K, 1M- (10pcs each), Pin header (40pin)- 2pcs

Combo of Electronic Components Project Kit or Breadboard | Capacitor | Resistor | LED & | Switch | Comes in a Box

Specification:-

• 5mm LED round shape
• 830 Points Half-Size Solderless Breadboard
• Cylindrical-shaped mini-shaft RC motor
• 0.25W power audio woofer speaker 
• 3-Terminal Positive Voltage Regulator
• Self-Lock latching mini push button
• 5v Piezoelectric Buzzer Beeper Alarm
• Aluminum Electrolytic Capacitors
• Multilayer Ceramic Capacitor

Kit includes: 9V Battery-1pcs, 9V Battery connector-1pcs, 830 points breadboard-1pcs, cylindrical shape Motor-1pcs, Diode(1N4007)-10pcs each, Zener Diode(3.3v)-10pcs, Single core Red & Black Wire-1mtr each, 1.2inch 16-ohm speaker-1pcs, Push Button-2pcs

Transistor (2N3906, BC557, BC558, 2N2222)5pcs each, Voltage Regulator (7805,7809,7812)-1pcs each, 5v Buzzer-1pcs, 5mm LED (red, blue, green, yellow, white)-5pcs each, IR Transmitter & Receiver-5pcs each, Variable Resistor (10k, 100k,1k,2k,5k)1pcs each, Ic's (4017, 555 timer)-1pcs each, Electrolytic Capacitor (1uf, 2.2uf, 4.7uf,47uf, 220uf, 100uf, 10uf)5pcs each, Ceramic Capacitor (104, 103, 101, 100, 102); 10 pieces each, 1/4-watt resistor (5.6, 15k, 470, 2.2, 390, 220)-10 pieces each

Continuity Tester Multi-Purpose Tool with Red LED Indicator & Buzzer Sound

Specification:-

• Length of the wire: 45cm
• Body Material: Plastic  
• A LED light indicator
• Easy to handle and operate
• Hard plastic body

1-8s Lipo Battery Voltage Tester with Buzzer Alarm

Specification:-

• Input: 1S-8S Battery
• Battery type: Lipo/LiFe/Li-ion/LiMn
• Voltage detection precision: 0.01V.
• Alarm set range: 2.7-3.8V
• Cell Voltage Display Range: 0.5-4.5V
• Total voltage display range: 0.5V-36V
• 1S test mode voltage range: 3.7-30V
• Low voltage alarm mode for 2-8S

Electromagnetic Rabbit Buzzer Mechanism

Specification:-

• Electromagnetic Coil
• Efficient Sound Production
• The red and yellow wires connect to a power source
• The black cylindrical part at the base is an electromagnet
• The metal piece above the coil moves when the magnet is activated.

Combo of Toy Battey | Battery Clip Connector | Buzzer | Rocker Switchs (5Pcs Each)

Specification:-

• Type: Piezoelectric Buzzer
• Input Voltage: 9-12V
• Current: <25MA
• High-performance battery
• Metal jacket body
• Nominal voltage : 9V
• Max. current withstand : 250V
• Max. power rating : 6A
• Long life approximately 10,000 clicks

Package Included:- 5 Pcs 9V Toy Battery, 5 Pcs Battery Clip Connector, 5 Pcs Rocker Switch, 5 Pcs 5V Buzzer, 5 Pcs 12V Buzzer

D 26 crossover network board High Frequency PAS 26 module

Specifications

1. Maximum power : 25W
2. Frequency response : 45Hz to 20kHz
3. Applicable Resistance : 4ohm
4. Applicable Speaker : 8 inch or less
5. High-temperature wire bass sound
6. High quality metalized polyester capacitors
7. Overcurrent, overload, and short circuit protection design

DBS, DB102S 1A 100V Bridge Rectifiers Diode pack of 5pcs

Specification

1. Case : DBS
2. Maximum respective peak reverse voltage : 100v
3. Maximum average rectified current : 1.0A
4. Maxim reverse current : 5.0µA
5. Non-Repetitive Peak Forward Surge Current : 50A
6. Maxim forward voltage : 1.1V

WOB, 2W04 2A 400V Bridge Rectifiers Diode pack of 5pcs

Specification

1. Case : WOB
2. Maximum respective peak reverse voltage : 400v
3. Maximum average rectified current : 2.0A
4. Maxim reverse current : 10.0µA
5. Non-Repetitive Peak Forward Surge Current : 50A
6. Maxim forward voltage : 1.1V

RS-2, KBP005 2A 50V Bridge Rectifiers Diode pack of 2pcs

Specification

1. Case : RS-2
2. Maximum respective peak reverse voltage : 50v
3. Maximum average rectified current : 2.0A
4. Maxim reverse current : 10.0µA
5. Non-Repetitive Peak Forward Surge Current : 50A
6. Maxim forward voltage : 1.1V

RS-2, KBP01 2A 100V Bridge Rectifiers Diode pack of 2pcs

Specification

1. Case : RS-2
2. Maximum respective peak reverse voltage : 100v
3. Maximum average rectified current : 2.0A
4. Maxim reverse current : 10.0µA
5. Non-Repetitive Peak Forward Surge Current : 50A
6. Maxim forward voltage : 1.1V

KBPC1, KBPC102 3A 200V Bridge Rectifiers Diode pack of 2pcs

Specification

1. Case : KBPC1
2. Maximum respective peak reverse voltage : 200v
3. Maximum average rectified current : 3.0A
4. Maxim reverse current : 10.0µA
5. Non-Repetitive Peak Forward Surge Current : 60A
6. Maxim forward voltage : 1.0V

KBPC25, KBPC1002 10A 200V Bridge Rectifiers Diode pack of 2pcs

Specification

1. Case : KBPC25
2. Maximum respective peak reverse voltage : 200v
3. Maximum average rectified current : 10.0A
4. Maxim reverse current : 5.0µA
5. Non-Repetitive Peak Forward Surge Current : 175A

KBPC25, KBPC1004 10A 400V Bridge Rectifiers Diode pack of 2pcs

Specification

1. Case : KBPC25
2. Maximum respective peak reverse voltage : 400v
3. Maximum average rectified current : 10.0A
4. Maxim reverse current : 5.0µA
5. Non-Repetitive Peak Forward Surge Current : 175A
6. Maxim forward voltage : 1.1V

KBU, KBU6A 6A 50V Bridge Rectifiers Diode pack of 2pcs

Specification

1. Case : KBU
2. Maximum respective peak reverse voltage : 50v
3. Maximum average rectified current : 6.0A
4. Maxim reverse current : 10.0µA
5. Non-Repetitive Peak Forward Surge Current : 250A
6. Maxim forward voltage : 1.1V

KBU, KBU6J 6A 600V Bridge Rectifiers Diode pack of 2pcs

Specification

1. Case : KBU
2. Maximum respective peak reverse voltage : 600v
3. Maximum average rectified current : 6.0A
4. Maxim reverse current : 10.0µA
5. Non-Repetitive Peak Forward Surge Current : 250A
6. Maxim forward voltage : 1.1V

GBU, GBU6005 6A 50V Bridge Rectifiers Diode pack of 2pcs

Specification

1. Case : GBU
2. Maximum respective peak reverse voltage : 50v
3. Maximum average rectified current : 6.0A
4. Maxim reverse current : 5.0µA
5. Non-Repetitive Peak Forward Surge Current : 175A
6. Maxim forward voltage : 1.0V

GBU, GBU608 6A 800V Bridge Rectifiers Diode pack of 2pcs

Specification

1. Case : GBU
2. Maximum respective peak reverse voltage : 800v
3. Maximum average rectified current : 6.0A
4. Maxim reverse current : 5.0µA
5. Non-Repetitive Peak Forward Surge Current : 175A
6. Maxim forward voltage : 1.0V

KBPC25-W, MB358W 35A 800V Bridge Rectifiers Diode pack of 2pcs

Specification

1. Case : KBPC25-W
2. Maximum respective peak reverse voltage : 800v
3. Maximum average rectified current : 35.0A
4. Maxim reverse current : 10.0µA
5. Non-Repetitive Peak Forward Surge Current : 400A
6. Maxim forward voltage : 1.1V

DIY Mini Music Reactive Kit With User Mannual And Video Tutorial

Specification

1. 100% Best quality and Branded Products
2. Diy Mini Music Reactive Kit
3. User Manual & Video Tutorial 
4. Battery Holder
5. Push Connector

74F521PC Logic IC Magnitude Comparator Bit Active Low Output A=B 20-PDIP

Specification:- 

• Package: PDIP20 (0.300", 7.62mm) 
• Mounting Style: Through Hole
• Logic Function: A = B
• Propagation Delay Time: 10 ns
• Supply Voltage - Min: 4.5 V
• Supply Voltage - Max: 5.5 V

CD4063BE Magnitude Comparator Bit Active Logic IC High Output AB 16-PDIP

Specification :-

• Package: PDIP16 (0.300", 7.62mm)
• Mounting Style: Through Hole
• Logic Function: A < B, A = B, A > B
• Propagation Delay Time: 140 ns, 175 ns
• Supply Voltage - Min: 3 V
• Supply Voltage - Max: 18 V
• Supply Current - Max: 100 uA

4-8S 40A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (7635)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature -40°C~85°C 

4-8S 60A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (7637)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature -40°C~85°C 

4-8S 80A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (7638)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature: -40°C~85°C 

4-8S 100A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (7639)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature: -40°C~85°C 

8-17S 40A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (763a)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature: -40°C~85°C 

8-17S 60A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (763c)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature: -40°C~85°C 

8-17S 80A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (763d)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature: -40°C~85°C 

8-17S 100A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (763e)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature: -40°C~85°C 

8-24S 40A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (763f)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature: -40°C~85°C 

8-24S 60A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (7640)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature: -40°C~85°C 

8-24S 80A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (7641)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• working temperature: -40°C~85°C 

8-24S 100A Smart Active Balance Li-Ion-LiFePO4 BMS (R24TK1A)

Specification:-

• Model Number: R24TK1A (7642)
• Cell sampling voltage range: 1.5V-4.9V 
• Operating voltage range: >10V 
• Balance method: Active Balance 
• Working power consumption: ≤1.25W 
• Working temperature: -40°C~85°C 

4S 1A Li-Ion/LiFePO4 Active Balancer Hardware

Specification:-

• Hardware active equalization specification 
• Number of battery pack strings: 4S  
• Balance current ≤ 1A 
• Balance mode - Active equilibrium  
• working temperature: -20°C~60°C 
• Model no. (48e8)

4S 1A Li-Ion/LiFePO4 Active Balancer Software

Specification:-

• Software active equalization 
• Number of battery pack strings - 4S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• working temperature: -20°C~60°C 
• Model no. (48ed)

6S 1A Li-Ion/LiFePO4 Active Balancer Hardware

Specification:-

• Software active equalization specification 
• Number of battery pack strings - 6S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• working temperature -20°C~60°C 
• Model no. (48e9)

7S 1A Li-Ion/LiFePO4 Hardware Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 7S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• working temperature -20°C~60°C 
• Model no. (48ea)

7S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization specification
• Number of battery pack strings - 7S
• Balance current ≤1A
• Balance mode - Active equilibrium
• working temperature -20°C~60°C
• Model no. (48ef)

8S 1A Li-Ion/LiFePO4 Hardware Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 8S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• working temperature: -20°C~60°C 
• Model no. (48eb)

Smart 8S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 8S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• working temperature -20°C~60°C 
• Model no. (48f1)

10S 1A Li-Ion/LiFePO4 Hardware Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 10S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• working temperature -20°C~60°C 
• Model no. (48ec)

Smart 10S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 10S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• working temperature -20°C~60°C 
• Model no. (48f2)

Smart 12S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 12S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• working temperature: -20°C~60°C 
• Model no. (48f3)

Smart 13S 1A Li-Ion/LiFePO4 Hardware Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings: 13S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• working temperature -20°C~60°C 
• Model no. (764a)

Smart 13S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 13S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• Working temperature: -20°C~60°C 
• Model no. (48f4)

Smart 14S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 14S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• Working temperature -20°C~60°C 
• Model no. (48f5)

Smart 15S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 15S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• Working temperature: -20°C~60°C 
• Model no. (48f6)

Smart 16S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 16S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• Working temperature -20°C~60°C 
• Model no. (46a5)

Smart 17S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 17S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• Working temperature -20°C~60°C 
• Model no. (48f8)

Smart 19S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 19S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• Working temperature -20°C~60°C 
• Model no. (521d)

Smart 20S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 20S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• Working temperature: -20°C~60°C 
• Model no. (48f9)

Smart 23S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 23S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• Working temperature -20°C~60°C 
• Model no. (73e9)

Smart 24S 1A Li-Ion/LiFePO4 Software Active Balancer

Specification:-

• Software active equalization 
• Number of battery pack strings - 24S  
• Balance current ≤1A  
• Balance mode - Active equilibrium  
• Working temperature -20°C~60°C 
• Model no. (48fa)