NEW ARRIVALS

STEAM Educational Learning Kit (Age 8+)

Specification:

• Kit Type: DIY Science & Robotics Educational Kit
• Recommended Age: 8+ years
• Total Components: 16+ electronic parts (motor, LEDs, buzzer, solar panel, resistors, switches, etc.)
• Power Source: Battery holder & solar panel (included)
• Learning Scope: Basic electronics, renewable energy, robotics fundamentals
• Durability: Reusable and safe for multiple projects

Kit Included:

DIY Line Follower Robot Kit | Arduino IDE Compatible | 3-Array IR Sensor | Robotics STEM Learning Kit for Students

Specification:

• Controller: Arduino Uno R3 compatible board
• Sensor: 3-Array IR Line Tracking Module
• Motor Driver: L298N or equivalent
• Motors: DC Gear Motors with wheels
• Chassis: DIY car frame with caster wheel
• Power: Battery holder included
• Programming: Arduino IDE

13.56MHz RFID Tag with Multicolor Keychain for Access Control Pack of 5

Specification:-

• Range: 0-10 cm
• Frequency: 13.56 MHz
• Passive RFID Tag key
• 32bit Unique ID
• Color: Multicolor 
• 64-bit data stream (Header+ID+Data+Parity)
• Reading Distance about 5 to 12 cm (depending upon the reader)

Level-2 Advanced Starter Kit Compatible with Arduino IDE & Uno R3 | RFID, Bluetooth & IoT Learning (114 Item)

Specification:-

• Complete Arduino Kit with 100+ components.
• Includes an Uno R3 and 830-point breadboard
• 12 x 12 x 7 mm tactile switch with cap
• Resistor type: 1/4 watt carbon film resistor
• SG90 Servo Motor
• 5V Piezoelectric Beep Buzzer
• USB Cable for Arduino Nano
• Resistor type: 1/4 watt carbon film resistor (220K, 330K, 1K)

Kit Included: 1 pcs Adruino Uno R3 | 1 pcs 830 Points Breadboard | 1 pcs USB Cable | 40 pcs Jumper Wires (Male to Male / Female to Male mix) | 1 pcs 1602 LCD Display | 1 pcs 7 Segment Display (1 Digit) | 1 pcs 4×4 Keypad | 1 pcs Stepper Motor | 1 pcs Stepper Motor Driver Module | 1 pcs Servo Motor (SG90) | 1 pcs Potentiometer (10K) | 1 pcs Active Buzzer | 1 pcs Passive Buzzer | 1 pcs IR Remote + IR Receiver | 1 pcs RTC (Real Time Clock) Module | 1 pcs RFID Module with Tag & Key | 1 pcs Joystick Module | 1 pcs Photoresistor (LDR Sensor) | 1 pcs Flame Sensor | 1 pcs Tilt Switch / Vibration Sensor (small module) | 1 pcs Sound Sensor Module | 1 pcs Water Sensor Module | 1 pcs DHT11 Temperature & Humidity Sensor | 1 pcs RGB LED Module | 1 pcs DC Motor Driver IC Module (L293D based) | 1 pcs 5V Relay Module | 1 pcs Battery Plug (9V Connector) | 30 pcs Resistor Pack (assorted values) | 15 pcs LEDs (Red, Green, Yellow)  | 5 pcs Push Button with Caps

DIY Self-Balancing Robot Car Kit | Uno R3 + L298N Motor Driver + MPU6050 | Compatible with Arduino IDE

Specification:-

• Main Controller: Uno R3 Board
• Motor Driver: L298N Dual H-Bridge
• Sensor: MPU6050 Gyroscope + Accelerometer
• Power Supply: Battery-powered (holder included)
• Compatibility: Arduino IDE / DIY Robotics Projects

3-in-1 Robotics Starter Kit | Multipurpose DIY Robot Kit | Compatible with Arduino Uno R3 (181 Item)

Specification:

• Includes an Uno R3 and a 400 point breadboard
• 12 x 12 x 7.3 mm tactile switch with cap
• ESP8266 Wireless Wi Fi Transceiver
• DC toy Motor Driver with wire
• 1 Digit 7 Segment LED Display
• Jumper Wire Cable 26AWG (21cm)
• Resistor type: 1/4 watt carbon film resistor
• Sensors: DHT11, Ultrasonic, etc.
• Complete Arduino Kit with 100+ components.

Kit Included: 1x Uno R3 Board | 1x Breadboard (400 points) | 1x 7 Segment Display (1 Digit) | 2x Push Buttons (with caps) | 1x Potentiometer | 1x DC Motor | 1x SG90 Servo Motor | 1x RGB LED Module | 2x Transistor PN2222 | 15x LEDs (Red, Green, Blue) | 1x Active Buzzer | 1x Passive Buzzer | 1x HC-SR04 Ultrasonic Sensor | 10x Resistors 220Ω | 10x Resistors 1kΩ | 40x Female-to-Female (F-F) Jumper Wires | 40x Male-to-Female (M-F) Jumper Wires | 40x Male-to-Male (M-M) Jumper Wires | 2x Diode 1N4001 | 1x Relay Module | 2x Line Sensor  | 2x Photoresistor Sensor  | 1x L293D Motor Driver Shield | 1x Battery Power Supply (with holder) | 1x Ultrasonic Sensor Holder | 1x 2WD Car Chassis

Smart Learning Robotics & IoT Kit | Beginner to Advanced STEM Project Kit | Compatible with Arduino IDE & Uno R3 (154 Item)

Specification:-

• Includes an Uno R3 and a 400 point breadboard
• 12 x 12 x 7 mm tactile switch with cap
• ESP8266 Wireless WiFi Transceiver
• DC toy Motor Driver with wire
• Resistor type: 1/4 watt carbon film resistor
• Sensors: DHT11, Ultrasonic, etc.
• Complete Arduino Kit with 100+ components.

Kit Included: 1 pcs Uno R3 Board | 1 pcs NodeMCU ESP8266 | 1 pcs Breadboard Small Size with 400 Points Solderless | 2 pcs Push Button with Caps | 1 pcs Potentiometer | 1 pcs ESP01 8266 | 1 pcs 7 Segment 1 Digit Cube Display | 1 pcs IC 74HC595 | 1 pcs Transistor PNP2222 | 15 pcs LEDs (Red, Blue, Green) | 1 pcs DHT11 with PCB (3 pin) | 1 pcs DC Motor | 1 pcs SG90 Servo Motor | 1 pcs RGB LED with PCB | 1 pcs 1602 I2C LCD Display | 1 pcs Active Buzzer | 1 pcs Passive Buzzer  | 1 pcs Ultrasonic Sensor HC-SR04 | 1 pcs HC05 Bluetooth Module | 50 pcs Resistors (220K, 330K, 1K, 22K, 15K assorted) | 20 pcs Jumper Wire (Male to Male) | 20 pcs Jumper Wire (Female to Female) | 20 pcs Jumper Wire (Female to Male) | 1 pcs Diode 1N4001 | 1 pcs 5V Relay Module | 2 pcs IR Line Sensor | 2 pcs Photoresistor | 1 pcs L293D Motor Driver Shield with soldered pins | 1 pcs Power Supply Box (6 Cell Holder) | 1 pcs Ultrasonic Sensor Holder | 1 pcs 2WD Car Chassis

Ultimate UNO R3 Professional Starter Kit | Compatible with Arduino IDE | DIY Electronics Kit (160 Item)

Specification:- 

• Complete Ultimate Arduino Professional Kit with 100+ components.
• Includes an Uno R3 and a large breadboard with a power supply.
• 12 x 12 x 7 mm tactile switches
• ESP8266 Wireless WiFi Transceiver
• L293D 4-Channel DC Motor Driver
• Resistor type: 1/4 watt carbon film resistor
• Modules: ESP8266 Wi-Fi, Bluetooth, RC522 RFID, and IR Remote.
• Sensors: PIR, DHT11, Ultrasonic, IR, Soil, Raindrop, Touch, etc.

Kit Included:

Male-Female Extension Wall Cord Cable | 3-Pin 1-Meter PVC | Suitable for Computers

Specification:

1. Type: 3-Pin Male-Female Extension Cable
2. Voltage Rating: 220–250V AC
3. Cable Length: 1 Meters
4. Color: White
5. Material: High-grade PVC
6. Connector Gender: Male-to-Female

Beginner's Kit for Uno R3 | DIY Electronics & STEM Starter Kit | Compatible with Arduino IDE (57 Item)

Specification:-

• Complete Arduino Kit with 100+ components.
• 12 x 12 x 7 mm tactile switch
• 5V Piezoelectric Beep Buzzer
• USB Cable for Arduino Nano
• SG90 Servo Motor
• UNO R3 AVR USB Development board
• Light Dependent Resistors sensor
• Resistor type: 1/4 watt carbon film resistor (220K, 330K)

Kit includes:-

1x Uno R3 Board | 1x USB Cable | 20x LEDs (Red, Yellow, Blue, Green) | 1x Potentiometer | 6x Push Button Switch | 2x Photoresistor | 20x Resistor | 1x RGB Led | 1x 7-Segment 1-Digit | 1x Breadboard 400 Point | 1x Buzzer | 1x Servo Motor | 1x Vibration Switch

12V 16.6A 200W SMPS LED Driver Power Supply | AC 175–265V to 12V DC Converter

Specification:-

1. Output Voltage: 12V
2. Output Current: 16.6A 
3. Output Power: 200W
4. Input Voltage: 175V/265V AC
5. Frequency: 50/60Hz
6. IP Level-Waterproof

13.56MHz RFID Tag with Black Keychain for Access Control Pack of 5

Specification:-

• Range: 0-10 cm
• Frequency: 13.56 MHz
• Passive RFID Tag key
• 32-bit Unique ID
• Color: Black
• 64-bit data stream (Header+ID+Data+Parity)
• Reading Distance about 5 to 12 cm (depending upon the reader)