NEW ARRIVALS

3-in-1 Robotics Starter Kit | Multipurpose DIY Robot Kit | Compatible with Arduino Uno R3 (181 Item)

Specification:

• Includes an Uno R3 and a 400 point breadboard
• 12 x 12 x 7.3 mm tactile switch with cap
• ESP8266 Wireless Wi Fi Transceiver
• DC toy Motor Driver with wire
• 1 Digit 7 Segment LED Display
• Jumper Wire Cable 26AWG (21cm)
• Resistor type: 1/4 watt carbon film resistor
• Sensors: DHT11, Ultrasonic, etc.
• Complete Arduino Kit with 100+ components.

Kit Included: 1x Uno R3 Board | 1x Breadboard (400 points) | 1x 7 Segment Display (1 Digit) | 2x Push Buttons (with caps) | 1x Potentiometer | 1x DC Motor | 1x SG90 Servo Motor | 1x RGB LED Module | 2x Transistor PN2222 | 15x LEDs (Red, Green, Blue) | 1x Active Buzzer | 1x Passive Buzzer | 1x HC-SR04 Ultrasonic Sensor | 10x Resistors 220Ω | 10x Resistors 1kΩ | 40x Female-to-Female (F-F) Jumper Wires | 40x Male-to-Female (M-F) Jumper Wires | 40x Male-to-Male (M-M) Jumper Wires | 2x Diode 1N4001 | 1x Relay Module | 2x Line Sensor  | 2x Photoresistor Sensor  | 1x L293D Motor Driver Shield | 1x Battery Power Supply (with holder) | 1x Ultrasonic Sensor Holder | 1x 2WD Car Chassis

28BYJ-48 5V DC Small Stepper Motor ULN2003 Driver Module

Specification:-

• Operating voltage: 5V
• Operating current: 0.5A
• Frequency: 100Hz
• Motor Model: 28BYJ-48
• Driver IC: ULN2003
• Step Angle: 5.625°/64 (gear reduction)
• Reduction Ratio: 1/64
• Phase: 4-phase, 5-wire motor

Basic Project Starter Kit Compatible with Arduino IDE & Uno R3 | DIY Electronics Kit (127 Item)

Specification:-

• Includes an Uno R3 and 400 point breadboard
• 1602 LCD Display
• 12 x 12 x 7 mm tactile switches
• 5mm round dip LED (Red, Yellow, Blue
• 16 x 2 Blue/White color LCD display
• Blue Short USB Data Charging Cable
• 1/4W Resistor (220K, 330K, 1K, 22K, 15K) 10 Pcs Each Value of Resistor

Kit Included: 1 pcs Compatible Uno R3 Board | 1 pcs USB Cable | 1 pcs Breadboard Small Size with 400 Points (Solderless) | 3 pcs Push Button | 1 pcs Potentiometer 10K | 1 pcs 5V Relay Module | 1 pcs DC Motor | 1 pcs SG90 Servo Motor | 1 pcs Passive Buzzer | 15 pcs LEDs (Assorted Colors – Red, Yellow, Blue) | 1 pcs DHT11 with PCB (4 pin) | 1 pcs Keypad 4×4 | 40 pcs Jumper Wire (Male to Male) | 50 pcs Resistors (220K, 330K, 1K, 22K, 15K) | 1 pcs 1602 LCD Display | 1 pcs 40 Pin Header | 2 pcs NPN Transistor | 2 pcs Diode 1N4001 | 1 pcs RGB LED | 1 pcs Photoresistor | 1 pcs Shift Register

Male-Female Extension Wall Cord Cable | 3-Pin 1-Meter PVC | Suitable for Computers

Specification:

1. Type: 3-Pin Male-Female Extension Cable
2. Voltage Rating: 220–250V AC
3. Cable Length: 1 Meters
4. Color: White
5. Material: High-grade PVC
6. Connector Gender: Male-to-Female

BT16R11 220V RF Remote Switch 32A | Long Range 3 KM | for Motor Pump & Industrial Use

Specification:-

• Model: BT16R11
• Operating Voltage: AC 220V
• Relay Load Capacity: 32A
• Frequency: 433MHz RF
• Control Range: Up to 3 KM (open area)
• Channels: 1-Channel relay output
• Power Input: Direct 220V AC supply
• Material: ABS housing + high-quality FR4 PCB
• Application Load: Motor pumps, heavy machinery, lighting, household appliances

Super Starter UNO R4 Minima Kit | DIY Electronics & Robotics Kit for Beginners to Advanced Users (105 Item)

Specification:-

• Compatible with UNO R4 Minima Board
• Fully supports Arduino IDE programming environment
• Includes a wide range of electronic components, sensors, and modules
• Plug-and-play breadboard for easy prototyping without soldering
• Durable and reusable components for multiple projects
• Suitable for beginners, hobbyists, and intermediate learners

Kit Included:
1x Compatible R4-Lite Minima Board | 1x Type-C Cable | 1x 830 Point Breadboard | 1x Servo Motor | 40x Male-to-Male & Male-to-Female Jumper Wires | 1x 0.96 inch OLED Display | 1x Photoresistor (LDR) | 1x DHT11 Temperature & Humidity Sensor | 1x Potentiometer 10K | 30x Resistor Pack – 220Ω, 1KΩ, 10KΩ | 1x Active Buzzer | 1x Passive Buzzer | 1x Ultrasonic Sensor (HC-SR04) | 6x Push Switch with caps | 1x RGB LED Module | 15x LEDs (Red, Green, Yellow) 1x Tilt Sensor | 1x IR Sensor | 1x Flame Sensor

12V 16.6A 200W SMPS LED Driver Power Supply | AC 175–265V to 12V DC Converter

Specification:-

1. Output Voltage: 12V
2. Output Current: 16.6A 
3. Output Power: 200W
4. Input Voltage: 175V/265V AC
5. Frequency: 50/60Hz
6. IP Level-Waterproof

3-in-1 Servo Motor Kit with SG90 Micro Servo | Digital Servo Tester | AA 4 Cell Battery Holder

Specification:-

• Digital Multi Servo Tester
• Operating Voltage: DC 4.8-6V
• AA 4 cells Battery holder
• Type : AA battery holder
• Output current : 6V
• SG90 Servo Motor
• Operating voltage:  3V to 7.2V
• Recommended voltage: 5V
• Stall torque : 1.2 kg/cm (4.8V)
• Max stall torque : 1.6 kg/cm (6V)
• The operating speed is 0.1s/60° (4.8V)
• Rotation: 0°-180°

Level-2 Advanced Starter Kit Compatible with Arduino IDE & Uno R3 | RFID, Bluetooth & IoT Learning (114 Item)

Specification:-

• Complete Arduino Kit with 100+ components.
• Includes an Uno R3 and 830-point breadboard
• 12 x 12 x 7 mm tactile switch with cap
• Resistor type: 1/4 watt carbon film resistor
• SG90 Servo Motor
• 5V Piezoelectric Beep Buzzer
• USB Cable for Arduino Nano
• Resistor type: 1/4 watt carbon film resistor (220K, 330K, 1K)

Kit Included: 1 pcs Adruino Uno R3 | 1 pcs 830 Points Breadboard | 1 pcs USB Cable | 40 pcs Jumper Wires (Male to Male / Female to Male mix) | 1 pcs 1602 LCD Display | 1 pcs 7 Segment Display (1 Digit) | 1 pcs 4×4 Keypad | 1 pcs Stepper Motor | 1 pcs Stepper Motor Driver Module | 1 pcs Servo Motor (SG90) | 1 pcs Potentiometer (10K) | 1 pcs Active Buzzer | 1 pcs Passive Buzzer | 1 pcs IR Remote + IR Receiver | 1 pcs RTC (Real Time Clock) Module | 1 pcs RFID Module with Tag & Key | 1 pcs Joystick Module | 1 pcs Photoresistor (LDR Sensor) | 1 pcs Flame Sensor | 1 pcs Tilt Switch / Vibration Sensor (small module) | 1 pcs Sound Sensor Module | 1 pcs Water Sensor Module | 1 pcs DHT11 Temperature & Humidity Sensor | 1 pcs RGB LED Module | 1 pcs DC Motor Driver IC Module (L293D based) | 1 pcs 5V Relay Module | 1 pcs Battery Plug (9V Connector) | 30 pcs Resistor Pack (assorted values) | 15 pcs LEDs (Red, Green, Yellow)  | 5 pcs Push Button with Caps

9V 1.2A Power Adapter 5.5x2.5mm Plug Compatible with TP-Link Router

Specification: 

1. Input voltage : 150V to 285V AC
2. Connector Size: 5.5mm x 2.5mm (Male Plug)
3. Output voltage : 9V
4. Power rating : 1.2A
5. Max. frequency range : 50 to 60 Hz
6. Model no: SSP-091
7. High-quality adapter with the latest and advanced technology

13.56MHz RFID Tag with Black Keychain for Access Control Pack of 5

Specification:-

• Range: 0-10 cm
• Frequency: 13.56 MHz
• Passive RFID Tag key
• 32-bit Unique ID
• Color: Black
• 64-bit data stream (Header+ID+Data+Parity)
• Reading Distance about 5 to 12 cm (depending upon the reader)

46-in-1 DIY Sensor Kit (37-in-1 + Extra Modules) | Compatible with Arduino IDE & Raspberry Pi

Specification:-

• Modules Included: 46 modules (37-in-1 sensor kit + 9 additional modules)
• Durability: High-quality, reusable modules designed for long-term experimentation
• Hall effect detection sensor (easily available)
• Joystick sensor Input voltage range: 3.3V to 5V
• Suitable for Arduino, AVR, and PIC microcontroller projects
• The sensor module kit is perfect for various DIY projects and robotics science projects
• Programming Support: Fully supports Arduino IDE, Python, and Scratch-based coding platforms

Package includes:
1x Real time clock | 1x Joystick | 1x 5v relay | 1x Big sound | 1x Small sound | 1x Tracking | 1x Avoidance | 1x Water sensor | 1x Flame sensor | 1x Linear hall | 1x Touch sensor | 1x Digital temperature | 1x Active buzzer | 1x Passive buzzer | 1x  rgb | 1x Ultrasonic sensor | 1x Two color led | 1x Mini two color led | 1x Reed | 1x Mini reed | 1x Mpu 6050 | 1x Heartbeat | 1x 7 Color led | 1x Mp1584en | 1x Push button | 1x Shock sensor | 1x Rotatory encoder | 1x Light cup | 1xTilt switch | 1x Ball switch | 1x Photo resistor | 1x Gas sensor | 1x Analog hall | 1x Magnetic hall | 1x Temp 18b20 | 1x Analog temp | 1x IR Receiver | 1x Light blocking | 1x Sd card reader | 1x IR emitter | 1x Temp and humidity | 1x Laser emitter | 1x Smd rgb | 1x Soil moisture sensor | 1x Tap module | 1x Breadboard power supply.