SENSORS & MODULES

FSR406 Square Shape High Quality Resistance Pressure Sensor

Specification:-

• Type: Force sensing resistor
• Model: FSR 406
• Force Sensitivity Range: 0.1–10.02 Newtons
• Stand-Off Resistance: >10M ohms
• Temp Operating Range: -30 - +70 ºC
• Length: 88mm
• Width: 43.7mm
• Thickness: 0.42mm

Smart NMC BMS Li-ion 14S 48V 40A Common port with Balance

Specification:-

• Battery Configuration: Smart BMS LiFePO4 14S 48V 40A 
• Continuous Discharge Current: 40A 
• Balance detect Voltage 3.8 
• Charge Current: 20A 
• Charge Voltage: 58.8V 
• Model no. (2188)

6S 10A NMC Battery Protection and Charger BMS Hardware

Specification:-

• Input Voltage B+ to B-: -0.3~+20V 
• Overcharge Detection voltage/1CELL: 4.28±0.05V 
• Over discharge Detection voltage/1CELL: 2.8 ± 0.1 V 
• Over current: 4-6A 
• Suggest working temperature: -20°C~+60°C 
• Model No.(115d)

Smart BMS LiFePO4 15S 48V 60A Common Port with Balance

Specification:-

• Battery Configuration: Smart BMS LiFePO4 15S 48V 60A
• Continuous Discharge Current: 60A 
• Over-Voltage Protection: 3.8V  
• Charge Current: 30A 
• Charge Voltage: 54.75V 
• Model no. (2198)

4S 5A Lithium Battery Balance Board

Specification:-

• Software active equalization 
• Number of battery pack strings: 4S  
• Balance current ≤5A  
• Balance mode - Active equilibrium  
• working temperature: -20°C~60°C 
• Model no. (5420)

ENC28J60 Ethernet Module 12-Pin

Specification:-

• 25MHz Crystal
• 5 V power supply pin
• Driver IC : ENC28J60-I/SO
• Ethernet Port: HanRun HR911105A
• Compatible For Arduino, SPI, AVR, PIC, LPC, STM32

Pin Configuration:

• 5V: 5V power supply
• GND: Ground
• LNT: Interrupt pin
• CLK: Clock output from ethernet controller
• SO: SPI Output
• WOL: Wake-on-LAN (optional)
• SCK: SPI Clock
• ST: SPI Input
• RST: Reset pin
• CS: Chip Select
• Q3:  that this is the RX 3.3V supply

1S 2A LFP BMS Same Port Hardware

Specification:-

• Input Voltage B+ to B-: -0.3~+24V 
• Over current 17~23A 
• Overcharge Detection voltage/1CELL: 4.25±0.05V 
• Over discharge Detection voltage/1CELL: 2.7 ± 0.1 V 
• suggest working temperature: -20°C~+60°C 

8mm x 1.2mm Strong Silver Disc Shape Neodymium Magnet Pack of 2

Specification:-

• Material: Neodymium (NdFeB)
• Shape: Disc
• Diameter: 8mm
• Thickness: 1.2mm
• Magnetization: Axial
• Operating Temperature: -40°C to +80°C

16S 60A BMS LFP Hardware Waterproof

Specification:-

• Battery Configuration: 16S for LiFePO4 (LFP) batteries 
• Continuous Discharge Current: 60A 
• Over-Voltage Protection: 3.8V  
• Balancing Current: 50mA  
• Charge Voltage: 58.4V 
• Model no. (10cb)

25mm x 2mm Strong Silver Disc Shape Neodymium Magnet

Specification:-

• Material: Neodymium (NdFeB)
• Shape: Disc 
• Dimensions: 25mm x 2mm
• Magnetization: Axial
• Operating Temperature: -40°C to +80°C
• Coating: Ni+Cu+Ni (Nickel Coated)

Smart BMS LiFePO4 23S 72V 60A Common Port with Balance

Specification:-

• Battery Configuration: Smart BMS LiFePO4 23S 72V 60A
• Continuous Discharge Current: 60A 
• Over-Voltage Protection: 3.8V  
• Charge Current: 30A 
• Charge Voltage: 83.95V 
• Model no. (21a2)

15S 100A LFP BMS Hardware (ZP16S005) (74d7)

Specification:-

• Model: ZP16S005
• Charging voltage: 3.6V Number of strings
• Cell voltage range: 2.0~3.75V 
• Continuous charging current: 100A 
• Continuous discharging current: 100A 
• Consumption of running: ≤150uA 
• -Circuit resistance: ≤10mR 
• Operating temperature: -20°C-75°C