SENSORS & MODULES

22μH 5A Ferrite Magnetic Inductor Coil 0.7mm Wire dia (13x6mm)

Specification:-

• Inductance: 22μH
• Core Material: Ferrite
• Outer Diameter: 13mm
• Height: 6mm
• Current Rating: 5A
• Wire Diameter: 0.7 mm
• Shape: Toroidal

5A 12V Overcurrent Protection AC Current Detection Sensor Module

Specification :-

• Output mode: Switch signal output
• Operating voltage: DC12V
• Operating current: <20MA
• The current detection range: AC 0.3A-5A
• Operating frequency range: 20Hz ~ 400Hz

300 x 300 x 1mm Flexible Magnetic Sheet with Adhesive Backing

Specifications:-

• Shape: Square Sheet
• Color: Black
• Flexible Magnet Sheet
• Magnetic Paper Holder, Fridge Magnet
• Application: Industrial Magnet

5V 30A 1-Channel Relay Module

Specification:-

• Relay Type: Single channel
• Operating Voltage: 5V DC
• Current Rating: 30 Amps
• Current Capacity: 30A at 250V AC or 30V DC

Pinouts:

• DC+: DC power supply positive pole
• DC-: DC power supply negative pole
• IN: signal triggering pin
• JD+: relay control voltage positive
• JD-: relay control voltage negative

Liquid PH 0-14 Value Detection Regulator Sensor Module

Specification:-

• PH range: 0-14 pH
• Heating voltage: 5±0.2V
• Working current: 5-10mA
• The response time: ≤ 5S
• Stability time: ≤ the 60S
• Power consumption: ≤ 0.5W
• Temperature range: 0-60°C

18650 3.7V 4.2V Battery Type-C Charger Board DC-DC Step-Up Boost Module

Specification:-

• Input voltage range 4.2V~6.5V
• Output voltage 4.2V-28V
• Maximum power 5W
• Temperature -40~80℃
• Color: Black.
• Material: PCB

Turbidity Sensor Module with Board

Specifications:-

• Working Voltage: 5V DC
• Current: 30mA (MAX)
• Response Time: <500mS
• Insulation Resistance: 100MΩ (Min)
• Operating temperature: -30 ° C to 80 ° C

47μH 15A Ferrite Magnetic Inductor Coil 1.2mm Wire dia (20x10mm)

Specification:-

• Inductance: 47μH
• Core Material: Ferrite
• Outer Diameter: 20mm
• Height: 10mm
• Current Rating: 15A
• Wire Diameter: 1.2 mm
• Shape: Toroidal

ENC28J60 Ethernet Module 12-Pin

Specification:-

• 25MHz Crystal
• 5 V power supply pin
• Driver IC : ENC28J60-I/SO
• Ethernet Port: HanRun HR911105A
• Compatible For Arduino, SPI, AVR, PIC, LPC, STM32

Pin Configuration:

• 5V: 5V power supply
• GND: Ground
• LNT: Interrupt pin
• CLK: Clock output from ethernet controller
• SO: SPI Output
• WOL: Wake-on-LAN (optional)
• SCK: SPI Clock
• ST: SPI Input
• RST: Reset pin
• CS: Chip Select
• Q3:  that this is the RX 3.3V supply

IRF540 Isolation Power Module Electronic Block 4-Channel MOSFET Switch

Specification:-

• MOSFET Type: IRF540
• Number of Channels: 4
• Control Voltage: 3.3V to 5V DC
• Load Voltage: Up to 100V DC
• Load Current: Up to 33A per channel

L298 Dual Motor Driver Shield For Arduino

Specifications:-

• Motor Driver IC: L298N
• Input Voltage: 5V
• Current per Channel: 2A (peak), 1.5A (continuous)
• Control Type: PWM (speed), Direction (forward/reverse)
• Heat Management

FS IA6B 2.4GHz 6 Channel PPM with iBus Port Receiver

Specification:-

• Model: FS-iA6B
• Operating Voltage (VDC):4.0 ~ 8.4V
• No. of Channels:6
• No. of Band:140
• Encoding: GFSK.
• RF Range:2.4055–2.475 GHz.
• Video Format Supported: NTSC/PAL